View STF202-22_69389.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

STF202-22
USB Upstream Port Filter & TVS For EMI Filtering and ESD Protection
Objective - March 03, 2000
&
STF202-30
TEL:805-498-2111 FAX:805-498-3804 WEB:http://www.Semtech.com
DESCRIPTION
The STF202 is a combination EMI filter and line termination device with integrated TVS diodes for use on upstream USB ports. It is constructed using a proprietary technology that allows passive components and TVS diodes to be integrated in the same package. Each device will provide termination, filtering, and ESD protection for one upstream USB port. The STF202 is an easily implemented solution for meeting the requirements of revision 1.1 of the Universal Serial Bus specification. USB line termination is achieved with series 22 or 30 resistors on both the D+ and D- USB lines. These resistors preserve signal integrity by matching the cable impedance to that of the differential driver. The 1.5k pull-up resistor completes the termination circuit on each line. This resistor is required by the USB specification to identify the equipment as either a fullspeed (connected to D+ line) or low-speed (connected to D- line) device. The 47pF capacitors are used to bypass high frequency energy to ground and for edge rate control of the USB signals. Finally, the STF202 contains TVS diodes for ESD protection of both (D+ & D-) data lines and the voltage bus (VBUS). The TVS diodes provide effective suppression of ESD voltages in excess of 15kV (air discharge) and 8kV (contact discharge) per IEC 1000-4-2, level 4. The small size and integrated feature of the STF202 minimizes required board space and increases system reliability. The STF202 is suitable for use in USB hubs, computers, peripherals, and portable devices.
FEATURES * Bidirectional EMI/RFI filtering and line termination * * * * * * *
with integrated ESD protection ESD protection for USB power (VBUS) and data lines (D+ & D-) to IEC 1000-4-2 Level 4 Filtering and termination for two USB data lines Different series resistors for impedance matching Low TVS operating voltage (5.25V) Low leakage current Small SOT-23 6L package Solid-state technology
MECHANICAL CHARACTERISTICS * EIAJ SOT-23 6L package * Molding compound flammability rating: UL 94V-0 * Marking : Marking Code * Packaging : Tape and Reel per EIA 481 APPLICATIONS * USB Hubs * Portable electronics * Cellular Handsets * Peripherals * Servers, Desktop, Notebook, and Handheld
Computers
ORDERING INFORMATION
Part Number STF202-22.TC STF202-30.TC Series Resistor 22 30 Qty per Reel 3,000 3,000 Reel Size 7" 7"
COMPONENT VALUES
Series Resistor (RS) STF202-22 STF202-30 Tolerance 22 30 10% Pull Up Resistor (RPU) 1.5k 1.5k 10% Termination Capacitor (C) 47 47 20%
SCHEMATIC & PIN CONFIGURATION
SOT-23 6L (Top View)
(c) 2000 SEMTECH CORP.
652 MITCHELL ROAD NEWBURY PARK CA 91320
STF202-22
USB Upstream Port Filter & TVS For EMI Filtering and ESD Protection
Objective - March 03, 2000
&
STF202-30
MAXIMUM RATINGS
Rating Steady-State Power ESD Air Discharge per IEC 1000-4-2 ESD Contact Discharge per IEC 1000-4-2 Lead Soldering Temperature (10 seconds) Operating Temperature Storage Temperature Symbol P VPP VPP TL Tstg Tj Value 100 16 10 260 -40 to +125 -55 to +150 Unit mW kV kV C C C
ELECTRICAL CHARACTERISTICS (T = 25C Unless Otherwise Noted)
STF202-xx
Parameter TVS Reverse Stand-Off Voltage TVS Reverse Breakdown Voltage TVS Reverse Leakage Current Symbol VRWM VBR IR It = 1mA VRWM = 5.25V, T=25C Between VBUS pin and ground VRWM = 3.3V, T=25C Between any data (D+, D-) pin and ground Between I/O pins and Gnd, each device VR = 0V, f = 1MHz Each Line Each Line Each Line Each Line Between I/O pins and Gnd, each line VR = 0V, f = 1MHz 20 27 1.35 10 6 5 Conditions Minimum Nominal Maximum 5.25 Units V V A
TVS Reverse Leakage Current
IR
1
A
Total TVS Junction Capacitance
Cj
pF
Series Resistor (STF202-22) Series Resistor (STF202-30) Pull Up Resistor Capacitor Total Capacitance
RS RS RUP C CTOT
22 30 1.5 47 60
24 33 1.65
k pF pF
MARKING CODES
Part Number Marking Code STF202-22 STF202-30 222 230
(c) 2000 SEMTECH CORP.
652 MITCHELL ROAD NEWBURY PARK CA 91320
STF202-22
USB Upstream Port Filter & TVS For EMI Filtering and ESD Protection
Objective - March 03, 2000
&
STF202-30
TYPICAL CHARACTERISTICS
ESD Clamping (8kV Contact) ESD Clamping (15kV Air)
Insertion Loss Characteristics
Analog Crosstalk (D+ to D-)
0 dB
0 dB
-20 dB
-10 dB
-60 dB
-20 dB
0.030MHz
2.0GHz
0.030 MHz
1 GHz
(c) 2000 SEMTECH CORP.
652 MITCHELL ROAD NEWBURY PARK CA 91320
STF202-22
USB Upstream Port Filter & TVS For EMI Filtering and ESD Protection
Objective - March 03, 2000
&
STF202-30
APPLICATIONS INFORMATION
Device Connection The STF202 is designed to provide termination, EMI filtering and ESD protection for two USB I/O lines. The equivalent circuit diagram is shown in Figure 1. The device is connected as follows: 1. Full-Speed Devices: For full-speed devices the pull-up resistor is connected to the D+ line. Pin 1 is connected to the voltage supply line (VBUS). The input of the D+ line is routed into pin 3 and out of pin 4. The input of the D- line is connected at pin 2 and the output at pin 5. Pin 6 is connected to ground. Figure 1 - STF202 Circuit Diagram
.
*
Low-Speed Devices: For low speed devices the pull-up resistor is connected to the D- line. Pins 1 is connected to the voltage supply line (VBUS). The input of the D- line is connected at pin 3 with the output taken at pin 4. The input of the D+ line is connected to pin 2 and the output is at pin 5. Pin 6 is connected to ground.
Figure 2 - STF202 Connection Diagram (Full Speed Devices)
1 2 3 6 5 4
USB Port Design Considerations The Universal Serial Bus (USB) specification requires termination and filtering components for proper operation. In addition, an open USB socket is vulnerable to hazardous ESD discharges in excess of 15kV. These discharges can may occur on the data lines or the voltage bus. The STF202 is an easily implemented solution designed to meet the termination & EMI filter requirements of the USB specification revision 1.1. It also provides ESD protection to IEC 61000-4-2, level 4. A simplified USB port is shown in Figure 3. USB line termination is achieved with series resistors on both the D+ and D- lines. These resistors preserve signal integrity by matching the cable impedance to that of the differential driver. 15k pull-down resistors are used to identify a downstream port while an upstream port is identified with a 1.5K pull up resistor on either the D+ (full speed devices) or the D- (low speed devices) data line. Capacitors are used to bypass high frequency energy to ground and for edge rate control of the USB signals. TVS diodes are added for ESD protection of both (D+ & D-) data lines and the voltage bus (VBUS). A power distribution switch and voltage regulator provide the power management functions of the port. Semtech provides a complete solution to simplify USB port design (Figure 4). The STF201 & STF202 integrate all of the components necessary for line termination, bidirectional EMI filtering, and ESD protection on downstream (STF201) or upstream (STF202) ports. The SC5826 is a dual port power switch that provides individual or ganged port switching, fault reporting, and inrush current limiting as required by the USB specification. The SC5205 ULDO provides a stable voltage to the USB controller. Board Placement & Layout Guidelines. Designing a USB hub to meet EMI & ESD immunity requirements requires a combination of optimum component placement, trace routing, and good circuit design practices. Some general guidelines are given below:
* * * * *
Avoid running D+ & D- signal line traces near high speed clock lines or similar signal lines. Avoid running critical signal lines near board edges. Locate the USB controller chip near the USB connectors. Place the STF202 near the USB connector to restrict transient coupling. Minimize the path length between the USB connector and the STF202
(c) 2000 SEMTECH CORP.
652 MITCHELL ROAD NEWBURY PARK CA 91320
STF202-22
USB Upstream Port Filter & TVS For EMI Filtering and ESD Protection
Objective - March 03, 2000
&
STF202-30
APPLICATIONS INFORMATION
Figure 3 - USB Port Components
Figure 4 - Typical USB Hub Design
(c) 2000 SEMTECH CORP.
652 MITCHELL ROAD NEWBURY PARK CA 91320
STF202-22
USB Upstream Port Filter & TVS For EMI Filtering and ESD Protection
Objective - March 03, 2000
&
STF202-30
OUTLINE DRAWING SOT23-6L
LAND PATTERN SOT23-6L
(c) 2000 SEMTECH CORP.
652 MITCHELL ROAD NEWBURY PARK CA 91320

▲Up To Search▲

Price & Availability of STF202-22

	To Download STF202-22 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .